Exactly How to Set up a Tub
Exactly How to Set up a Tub
Blog Article
Each person has got their own unique perception in relation to A Step-by-Step Guide to Installing a Bathtub.
:max_bytes(150000):strip_icc()/convert-tub-to-shower-4156975-05-db9a69eb718545759045e6e39b4cfacf.jpg)
Setting up a bathtub isn't precisely brain surgery, however it does call for solid plumbing, woodworking, and often, tiling skills. Replacing an old bath tub with a new one is likewise a reasonably difficult job. If the old tub is readily obtainable, the task can move immediately; if you have to open a wall surface to remove the old tub and also place the new tub, the job is a lot harder. In either case, the job is within a residence handyman's skills, although you will require an assistant to vacate the old tub as well as embeded in the new one. Make certain you have actually certified on your own for the work and fit trying it. Rather than hiring a specialist to take over a halfway-completed job, it is better to take into consideration utilizing one before you start. Opportunities are you might need an expert plumber to make tube links.
This post will certainly help you mount a brand-new bath tub in your shower room if you have actually currently acquired a new tub and also don't need to alter the setup of your previous water system pipes.
Your tools and also material checklist must comprise the following:
Removing Old Touches
If you need to replace old taps with new ones as a part of your installment, after that the first thing you should do is disconnect the supply of water. After doing so, switch on the taps to drain any type of water remaining in the system. The process of removing the existing taps can be quite problematic due to the restricted access that is usually the instance.
Utilize a basin wrench (crowsfoot spanner) or a faucet device to reverse the nut that attaches the supply pipelines to the taps. Have a towel all set for the continuing to be water that will certainly originate from the pipelines. When the supply pipes have been removed, make use of the very same device to loosen the nut that holds the taps onto the bath/basin. You will require to quit the single taps from turning during this procedure. As soon as the faucets have been removed, the holes in the bath/basin will need to be cleansed of any kind of old securing compound.
Before moving on to fit the brand-new taps, compare the pipe links on the old faucets to the new taps. If the old faucets are longer than the new faucets, after that a shank adapter is required for the new faucets to fit.
Suitable New Taps
If the tails of the new faucets are plastic, after that you will need a plastic adapter to avoid damage to the string. One end of the adapter fits on the plastic tail of the tap and the various other end supplies a connection to the existent supply pipelines.
If you need to fit a monobloc, then you will certainly need reducing couplers, which attaches the 10mm pipeline of the monobloc to the conventional 15mm supply pipe.
Next off, position the faucet in the mounting opening in the bath/basin guaranteeing that the washers are in place between the faucet as well as the sink. Secure the faucet in place with the manufacturer supplied backnut. When the faucet is securely in position, the supply pipes can be attached to the tails of the taps. The taps can either be linked by utilizing corrugated copper piping or with regular faucet ports. The former kind ought to be attached to the faucet finishes initially, tightening just by hand. The supply pipelines can later on be connected to the other end. Tighten up both ends with a spanner after both ends have been attached.
Mounting the Tub
Using the two wood boards under its feet, position the tub in the needed placement. The wood boards are useful in uniformly spreading the weight of the bathtub over the area of the boards instead of concentrating all the weight onto four little factors.
The next objective is to ensure that the bath tub is leveled all round. This can be achieved by inspecting the level and also changing the feet on the bath tub till the level checks out level.
To install taps, fit the bottom of the furthest flexible tap adapter to the proper supply pipeline by making a compression join; then do the exact same for the various other faucet.
Turn on the water system and also examine all joints as well as new pipework for leakages and tighten them if required. Fill the bath tub as well as likewise check the overflow outlet and the typical electrical outlet for leaks.
Ultimately, take care of the bath paneling as explained in the supplier's instruction manual. Tiling as well as sealing around the bath tub ought to wait till the bathtub has been made use of at least once as this will resolve it into its final placement.
Preparing for the Setup
To start with, the supporting structure supplied with the bath must be fitted (if required) according to the producer's directions. Next off, fit the taps or mixer to the tub. When suitable the faucet block, it is essential to make sure that if the tap features a plastic washer, it is fitted in between the bath and also the faucets. On a plastic bath, it is likewise reasonable to fit a supporting plate under the taps system to avoid pressure on the bath tub.
Fit the flexible tap ports to the bottom of both faucets making use of 2 nuts and olives (in some cases provided with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet opening, and then pass the outlet with the hole in the bath. Utilize the nut provided by the supplier to fit the plug-hole. Check out the plug-hole outlet for an inlet on the side for the overflow pipe.
Next, fit the end of the versatile overflow pipeline to the overflow electrical outlet. Afterwards, screw the pipeline to the overflow face which must be fitted inside the bathroom. See to it you make use of every one of the provided washing machines.
Attach the catch to the bottom of the waste electrical outlet on the bath tub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, and also screw on the catch to the electrical outlet. Attach all-time low of the overflow tube in a comparable manner.The bathroom must currently prepare to be fitted in its final setting.
Tiling Around the Tub
In the area where the bath meets the ceramic tile, it is required to seal the joins with a silicone rubber caulking. This is essential as the fitting can relocate sufficient to split a stiff seal, triggering the water to penetrate the wall between the bathroom and the tiling, leading to complications with wetness and also possible leakages to the ceiling listed below.
You can pick from a range of coloured sealants to blend in your components and also installations. They are offered in tubes and cartridges, and can securing spaces up to a width of 3mm (1/8 inch). If you have a bigger gap to fill, you can load it with spins of soaked paper or soft rope. Keep in mind to always fill the bath tub with water prior to sealing, to allow for the activity experienced when the bathtub is in usage. The sealant can break rather early if you do not consider this motion prior to securing.
Conversely, ceramic coving or quadrant floor tiles can be utilized to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use and also cut to dimension, are also easily readily available on the market. It is a good idea to fit the floor tiles making use of waterproof or water resistant glue as well as cement.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
We had been guided to that editorial on A Step-by-Step Guide to Installing a Bathtub through an acquaintance on our other web page. Do you know about anybody else who is excited by the topic? Feel free to promote it. Thanks a lot for taking the time to read it.
Book-Now
Report this page